寡核苷酸与DNA的点击化学标记
Click chemistry is a versatile reaction that can be used for the synthesis of a variety of conjugates. Virtually any biomolecules can be involved, and labeling with small molecules, such as fluorescent dyes, biotin, and other groups can be readily achieved.
Click chemistry reaction takes place between two components: azide and alkyne (terminal acetylene). Both azido and alkyne groups are nearly never encountered in natural biomolecules. Hence, the reaction is highly bioorthogonal and specific. If there is a need to label an oligonucleotide, alkyne-modified oligonucleotides can be ordered at many of the custom oligo-synthesizing facilites and companies.
We recommend using the following general protocol for Click chemistry labeling of alkyne-modified oligonucleotides with azides produced by Lumiprobe Corp. The auxiliary reagents can be ordered at Lumiprobe Corp..
- Calculate the volumes of reagents required for Click chemistry labeling using the table below. Prepare the required stock solutions (see Appendix).
Reagent |
Final concentration in the mixture |
Stock solution concentration |
Oligonucleotide, alkyne-modified |
Varies (20 – 200 uM) |
varies |
Azide |
1.5 x (oligonucleotide concentration) |
10 mM in DMSO |
DMSO |
50 vol % |
– |
Ascorbic acid |
0.5 mM |
5 mM in water |
Cu-TBTA complex |
0.5 mM |
10 mM in 55 vol % DMSO |
- Dissolve alkyne-modified oligonucleotide or DNA in water in a pressure-tight vial.
- Add 2M triethylammonium acetate buffer, pH 7.0, to final concentration 0.2 M.
- Add DMSO, and vortex.
- Add azide stock solution (10 mM in DMSO), and vortex.
- Add the required volume of 5mM Ascorbic Acid Stock solution to the mixture, and vortex briefly.
- Degass the solution by bubbling inert gas in it for 30 seconds. Nitrogen, argon, or helium can be used.
- Add the required amount of 10 mM Copper (II)-TBTA Stock in 55% DMSO to the mixture. Flush the vial with inert gas and close the cap.
- Vortex the mixture thoroughly. If significant precipitation of azide is observed, heat the vial for 3 minutes at 80°C, and vortex.
- Keep at room temperature overnight.
- Precipitate the conjugate with acetone (for oligonucleotides) or with ethanol (for DNA). Add at least 4-fold volume of acetone to the mixture (If the volume of the mixture is large, split in several vials). Mix thoroughly and keep at -20°C for 20 minutes.
- Centrifuge at 10000 rpm for 10 minutes.
- Discard the supernatant.
- Wash the pellet with acetone (1 mL), centrifuge at 10000 rpm for 10 minutes.
- Discard the supernatant, dry the pellet, and purify the conjugate by RP-HPLC or PAGE.
Appendix. Preparation of stock solutions of the reagents used for click-chemistry labeling and conjugation
5 mM Ascorbic Acid Stock
Preparation |
Dissolve 18 mg of ascorbic acid in 20 mL of distilled water. |
Storage |
Ascorbic acid is readily oxidized by air. The solution is stable for one day. Use fresh preparations for Click chemistry. |
©
金山科研平台 Thermo Fisher官网Nunc、QSP、Nalgene、Invitrogen、Gibco耗材试剂授权一级代理是专业的授权总代理区域代理经销平台。
© 如需询价,请加客服QQ:1749072012 、客服微信:jinshanbio,或发送邮件到1749072012@qq.com
© 平台为生命科学研究相关领域提供一站式耗材试剂仪器解决方案和采购服务,数据资源基于CC协议。
© 本文地址:
https://thermonunc.cn/thread-23269.htm
特别声明:以上内容(如有图片亦包括在内)来源于授权厂家或网络,如有侵权,请联系客服删除,本平台不提供信息校正和存储服务。
Notice: The content above (including the pictures if any)comes from authorized manufacturers or networks. In case of infringement, please contact to delete it. This platform does not provide information storage services.